Metasurface interferometry toward quantum sensors

  • Light: Science & Applications  8, Article number: 70 (2019)
More Information
  • Corresponding author:
    Thomas Zentgraf (
  • Received: 22 March 2019
    Revised: 08 July 2019
    Accepted: 21 July 2019
    Published online: 14 August 2019


  • Optical metasurfaces open new avenues for the precise wavefront control of light for integrated quantum technology. Here, we demonstrate a hybrid integrated quantum photonic system that is capable of entangling and disentangling two-photon spin states at a dielectric metasurface. Via the interference of single-photon pairs at a nanostructured dielectric metasurface, a path-entangled two-photon NOON state with circular polarization that exhibits a quantum HOM interference visibility of 86 ± 4% is generated. Furthermore, we demonstrate nonclassicality andphase sensitivity in a metasurface-based interferometer with a fringe visibility of 86.8 ± 1.1% in the coincidence counts. This high visibility proves the metasurface-induced path entanglement inside the interferometer. Our findings provide a promising way to develop hybrid-integrated quantum technology operating in the high-dimensional mode space in various applications, such as imaging, sensing, and computing.
  • 加载中
  • [1] Sangouard, N. et al. Quantum repeaters based on atomic ensembles and linear optics. Rev. Mod. Phys. 83, 33-44 (2011). doi:  10.1103/RevModPhys.83.33
    [2] Hensen, B. et al. Loophole-free Bell inequality violation using electron spins separated by 1.3 kilometres. Nature 526, 682-686 (2015). doi:  10.1038/nature15759
    [3] Shalm, L. K. et al. Strong loophole-free test of local realism. Phys. Rev. Lett. 115, 250402 (2015). doi:  10.1103/PhysRevLett.115.250402
    [4] Tillmann, M. et al. Experimental boson sampling. Nat. Photonics 7, 540-544 (2013). doi:  10.1038/nphoton.2013.102
    [5] Broome, M. A. et al. Photonic boson sampling in a tunable circuit. Science 339, 794-798 (2013). doi:  10.1126/science.1231440
    [6] Spring, J. B. et al. Boson sampling on a photonic chip. Science 339, 798-801 (2013). doi:  10.1126/science.1231692
    [7] Peruzzo, A. et al. Quantum walks of correlated photons. Science 329, 1500-1503 (2010). doi:  10.1126/science.1193515
    [8] Giovannetti, V., Lloyd, S. & Maccone, L. Advances in quantum metrology. Nat. Photonics 5, 222-229 (2011). doi:  10.1038/nphoton.2011.35
    [9] Wang, J. W. et al. Multidimensional quantum entanglement with large-scale integrated optics. Science 360, 285-291 (2018). doi:  10.1126/science.aar7053
    [10] Molina-Terriza, G., Torres, J. P. & Torner, L. Twisted photons. Nat. Phys. 3, 305-310 (2007). doi:  10.1038/nphys607
    [11] Wang, X. L. et al. Quantum teleportation of multiple degrees of freedom of a single photon. Nature 518, 516-519 (2015). doi:  10.1038/nature14246
    [12] Khorasaninejad, M. et al. Metalenses at visible wavelengths: diffraction-limited focusing and subwavelength resolution imaging. Science 352, 1190-1194 (2016). doi:  10.1126/science.aaf6644
    [13] Wang, S. M. et al. A broadband achromatic metalens in the visible. Nat. Nanotechnol. 13, 227-232 (2018). doi:  10.1038/s41565-017-0052-4
    [14] Yue, F. Y. et al. Vector vortex beam generation with a single plasmonic metasurface. ACS Photonics 3, 1558-1563 (2016). doi:  10.1021/acsphotonics.6b00392
    [15] Shalaev, M. I. et al. High-efficiency all-dielectric metasurfaces for ultracompact beam manipulation in transmission mode. Nano Lett. 15, 6261-6266 (2015). doi:  10.1021/acs.nanolett.5b02926
    [16] Huang, L. L. et al. Three-dimensional optical holography using a plasmonic metasurface. Nat. Commun. 4, 2808 (2013). doi:  10.1038/ncomms3808
    [17] Li, G. X. et al. Continuous control of the nonlinearity phase for harmonic generations. Nat. Mater. 14, 607-612 (2015). doi:  10.1038/nmat4267
    [18] Almeida, E., Bitton, O. & Prior, Y. Nonlinear metamaterials for holography. Nat. Commun. 7, 12533 (2016). doi:  10.1038/ncomms12533
    [19] Yu, N. F. & Capasso, F. Flat optics with designer metasurfaces. Nat. Mater. 13, 139-150 (2014). doi:  10.1038/nmat3839
    [20] Genevet, P. et al. Recent advances in planar optics: from plasmonic to dielectric metasurfaces. Optica 4, 139-152 (2017). doi:  10.1364/OPTICA.4.000139
    [21] Lin, D. M. et al. Dielectric gradient metasurface optical elements. Science 345, 298-302 (2014). doi:  10.1126/science.1253213
    [22] Jha, P. K. et al. Metasurface-enabled remote quantum interference. Phys. Rev. Lett. 115, 025501 (2015). doi:  10.1103/PhysRevLett.115.025501
    [23] Jha, P. K. et al. Metasurface-mediated quantum entanglement. ACS Photonics 5, 971-976 (2018). doi:  10.1021/acsphotonics.7b01241
    [24] Stav, T. et al. Quantum entanglement of the spin and orbital angular momentum of photons using metamaterials. Science 361, 1101-1104 (2018). doi:  10.1126/science.aat9042
    [25] Wang, K. et al. Quantum metasurface for multiphoton interference and state reconstruction. Science 361, 1104-1108 (2018). doi:  10.1126/science.aat8196
    [26] Liu, H. C. et al. Single-pixel computational ghost imaging with helicity-dependent metasurface hologram. Sci. Adv. 3, e1701477 (2017). doi:  10.1126/sciadv.1701477
    [27] Malik, M. & Boyd, R. W. Quantum imaging technologies. Riv. Nuovo Cim. 37, 273-332 (2014).
    [28] Degen, C. L., Reinhard, F. & Cappellaro, P. Quantum sensing. Rev. Mod. Phys. 89, 035002 (2017). doi:  10.1103/RevModPhys.89.035002
    [29] O'Brien, J. L. Optical quantum computing. Science 318, 1567-1570 (2007). doi:  10.1126/science.1142892
    [30] Malik, M. et al. Multi-photon entanglement in high dimensions. Nat. Photonics 10, 248-252 (2016). doi:  10.1038/nphoton.2016.12
    [31] Bomzon, Z. et al. Space-variant pancharatnam-berry phase optical elements with computer-generated subwavelength gratings. Opt. Lett. 27, 1141-1143 (2002). doi:  10.1364/OL.27.001141
    [32] Dowling, J. P. Quantum optical metrology - the lowdown on high-N00N states. Contemp. Phys. 49, 125-143 (2008). doi:  10.1080/00107510802091298
    [33] Grice, W. P. & Walmsley, I. A. Spectral information and distinguishability in type-II down-conversion with a broadband pump. Phys. Rev. A56, 1627-1634 (1997).
    [34] Franson, J. D. Bell inequality for position and time. Phys. Rev. Lett. 62, 2205-2208 (1989). doi:  10.1103/PhysRevLett.62.2205
    [35] Edamatsu, K., Shimizu, R. & Itoh, T. Measurement of the photonic de Broglie wavelength of entangled photon pairs generated by spontaneous parametric down-conversion. Phys. Rev. Lett. 89, 213601 (2002). doi:  10.1103/PhysRevLett.89.213601
通讯作者: 陈斌,
  • 1. 

    沈阳化工大学材料科学与工程学院 沈阳 110142

  1. 本站搜索
  2. 百度学术搜索
  3. 万方数据库搜索
  4. CNKI搜索


Article Metrics

Article views(5) PDF downloads(0) Citation(0) Citation counts are provided from Web of Science. The counts may vary by service, and are reliant on the availability of their data.

Metasurface interferometry toward quantum sensors

  • 1. Paderborn University, Department of Physics, Warburger Str. 100, 33098 Paderborn, Germany
  • 2. University of Stuttgart, 4th Physics Institute, Pfaffenwaldring 57, 70569 Stuttgart, Germany
  • 3. Southern University of Science and Technology, Department of Materials Science and Engineering, Shenzhen Institute for Quantum Science and Engineering, 518055 Shenzhen, China
  • Corresponding author: Thomas Zentgraf,


Abstract: Optical metasurfaces open new avenues for the precise wavefront control of light for integrated quantum technology. Here, we demonstrate a hybrid integrated quantum photonic system that is capable of entangling and disentangling two-photon spin states at a dielectric metasurface. Via the interference of single-photon pairs at a nanostructured dielectric metasurface, a path-entangled two-photon NOON state with circular polarization that exhibits a quantum HOM interference visibility of 86 ± 4% is generated. Furthermore, we demonstrate nonclassicality andphase sensitivity in a metasurface-based interferometer with a fringe visibility of 86.8 ± 1.1% in the coincidence counts. This high visibility proves the metasurface-induced path entanglement inside the interferometer. Our findings provide a promising way to develop hybrid-integrated quantum technology operating in the high-dimensional mode space in various applications, such as imaging, sensing, and computing.

  • Integrated quantum technology is widely used to enable quantum applications in various systems for secure quantum communication1-3 as well as in quantum simulation4-7 and quantum metrology8. Although significant progress in terms of large-scale integration in one generic material has been achieved9, highly miniaturized integrated systems are required for more complex functionalities, such as teleporting twisted photons10 in a high-dimensional spin-orbital angular momentum (OAM) space11. However, the on-chip manipulation of circularly polarized photons is still an unsolved problem.

    State-of-the-art metasurfaces essentially achieve any kind of manipulation of light wavefronts for applications such as ultra-flat lenses for imaging12, 13, vector beam generation14, 15, optical holography16, and even nonlinear phase manipulation17, 18. These diverse functionalities can be achieved by tailoring the local geometries of the nanostructured surfaces. While all these concepts solely rely on the classical electromagnetic description, the potential of metasurfaces for quantum applications is still widely unexplored. However, as versatile optical elements for locally altering the amplitude, phase, and polarization of light19-21, metasurfaces can provide new functionalities to miniaturized quantum systems.

    Recently, few initiatives have been taken to investigate the potential of metasurfaces in quantum optics. Jha et al.22, 23 theoretically proposed that a metasurface can induce quantum interference between orthogonal radiative transition states of atoms and quantum entanglement between two qubits. Later, it was demonstrated that the entanglement of the spin and orbital angular momentum of a single photon can be generated via a metasurface24. In addition, the metasurface can provide a compact solution for quantum state reconstruction25. However, thus far, there is only limited experimental evidence revealing whether metasurfaces are suited tostate manipulation in quantum optical experiments. If the current metasurface technology can be directly applied to practical quantum applications, then metasurfaces can offer advanced solutions for quantum imaging26, 27, sensing28, and computing29.

    Here, we demonstrate the entanglement and disentanglement of two-photon states using an all-dielectric metasurface. Our metasurface allows the generation of path-entangled NOON states with circular polarization due to the quantum interference effect. We observe photon bunching within two spatially distinct output channels of the metasurface. Passing the same metasurface the second time, the generated path-entangled two-photon spin state can be disentangled without introducing additional phase information. Our experiments indicate that metasurfaces are perfectly suited to provide large-scale and high-dimensional quantum functionalities with properties that go far beyond the conventional optical elements. Thus, the hybrid integration of quantum optical elements together with metasurfaces offers the potential to deliver robust multiphoton entanglement and high-dimensional quantum applications, which allows to encode more information in the high-dimensional domain by combining OAM with hybrid space-polarization entanglement30.

  • For the experiment, we designthe metasurface to deflect the incident light into two different output directions under angles of ±10°. The deflection is obtained by using a space-variant Pancharatnam-Berryphase that results from the polarization conversion of the transmitted light31. As a platform for the metasurface, we use silicon nanofin structures. They act as local halfwave plates, which convert the circular polarization states into their cross polarization and add a spatial phase term based on their orientation angle. For our design, we choose a linear phase gradient, which diffracts the incoming light under the desired angle. We note that the sign of the phase gradient explicitly depends on the helicity of the circularly polarized light, which effectively makes our metasurface a spatial separator for the circular polarization states (for more details, see Supplementary Information).

  • Precise control and preparation of multiphoton entanglement are of fundamental interest for quantum technologies. With the accurate manipulation of the single photons' wavefront by a metasurface, spatial and polarization-based entanglement can be achieved. In our case, the metasurface is designed to spatially separate the generated circular polarization states of light and thus enforces a quantum state's representation in that particular basis, as sketched in Fig. 1a. For the particular quantum state $|{\mathrm{\Psi }}\rangle = \hat a_H^\dagger \hat a_V^\dagger |0 \rangle$, such a process at the metasurface leads to an entangled state. Note that we use the indices H and V for the two linear polarizations states and L and R for the circular polarization states. Starting with relations between the photon creation operators

    Fig. 1  Spatial entanglement and disentanglement of a two-photon state at a metasurface.

    a If a single photon pair with orthogonal linear polarization is inserted into the metasurface, it is divided into its circular polarization components. Since the inserted quantum state is a two-photon NOON state in the circular polarization basis, both photons will always choose the same output channel, and spatial entanglement is obtained. b The situation reverses for the insertion of a spatially entangled NOON state into the metasurface. The quantum interference leads to a projection back to the original orthogonal linear polarization states, and the photon pair is spatially disentangled
    $$ \begin{array}{l}\hat a_L^\dagger = \frac{1}{{\sqrt 2 }}\left( {\hat a_H^\dagger + i \cdot \hat a_V^\dagger } \right)\\ \hat a_R^\dagger = \frac{1}{{\sqrt 2 }}\left( {\hat a_H^\dagger - i \cdot \hat a_V^\dagger } \right)\end{array} $$ (1)

    the metasurface enforces a change in the initial quantum state $|{\mathrm{\Psi }}\rangle$ in the circular basis as

    $$ |{\mathrm{\Psi }} \rangle = \hat a_H^\dagger \hat a_V^\dagger |0\rangle = - \frac{i}{2}\left( {\hat a_L^\dagger \hat a_L^\dagger - \hat a_R^\dagger \hat a_R^\dagger } \right)|0\rangle $$ (2)

    which corresponds to a two-photon NOON state. In general, NOON states are entangled N-photon quantum states, which are commonly used for quantum metrology. Formally, these states can be written as a superposition of two quantum states with all photons allocated in only one of the two channels32

    $$ | {{\mathrm{\Psi }}_{{\mathrm{NOON}}}} \rangle = \frac{1}{{\sqrt 2 }}\left( {| N\rangle |0\rangle + |0\rangle| N \rangle } \right) $$ (3)

    Through metasurface-induced spatial separation of the two polarization channels, this path-encoded quantum state cannot be decomposed into two single-photon states and is therefore path-entangled.

    Interestingly, the same metasurface can be used in the reverse process, in which the circular polarization states are spatially recombined to disentangle the generated state. We utilize the polarization basis change functionality to build a metasurface-based interferometer. By introducing a phase delay φ between the two circular polarization channels and using the conversion of the polarization states of the metasurface, we obtain the quantum state

    $$ \begin{array}{l}|{\mathrm{\Psi }} \rangle _\varphi = - \frac{i}{2}\left( {\hat a_L^\dagger \hat a_L^\dagger e^{ - i2\varphi } - \hat a_R^\dagger \hat a_R^\dagger } \right)| 0 \rangle \\ = \frac{1}{2}\left( {e^{ - i2\varphi } + 1} \right)\hat a_H^\dagger \hat a_V^\dagger |0\rangle - \frac{i}{4}\left( {e^{ - i2\varphi } - 1} \right)\\\left( {\hat a_H^\dagger \hat a_H^\dagger - \hat a_V^\dagger \hat a_V^\dagger } \right)| 0 \rangle \end{array} $$ (4)

    For the case where $\varphi = {\mathrm{n\pi }}, \, ({\mathrm{n}}\epsilon {\Bbb Z})$, the output state after passing through the metasurface twice is the same as the initial two-photon state $\hat a_H^\dagger \hat a_V^\dagger |0\rangle$, which is disentangled (as shown in Fig. 1b). In the case of $\varphi = \left({{\mathrm{n}} + \frac{1}{2}} \right){\mathrm{\pi }}, \, ({\mathrm{n}}\epsilon {\Bbb Z})$, the output state $i \cdot \frac{1}{2} ({\hat a_H^\dagger \hat a_H^\dagger - \hat a_V^\dagger \hat a_V^\dagger })|0\rangle$ is entangled even after spatial recombination, as it cannot be decomposed in either polarization base.

  • First, we investigate the NOON-state generation at the metasurface. A key quantum feature of the NOON state is its photon bunching characteristics, i.e., we expect that both photons will always choose the same metasurface output channel after inserting the quantum state $\hat a_H^\dagger \hat a_V^\dagger | 0 \rangle$. To demonstrate this bunching effect, we use the setup shown in Fig. 2. It contains four logical parts: a two-photon source for the generation of the initial quantum state $|1_H\rangle|1_V\rangle$, a Michelson interferometer to adjust the time delay between these two photons, a metasurface as a quantum interference device, and a single-photon detection system. To control the time delay between the two photons, we use a modified Michelson interferometer with a PBS cube and two quarter-wave plates. Since the time delay directly influences the temporal overlap between both photons, we utilize it to enable $(\tau = 0)$ and disable $(\tau \to \infty)$ the quantum interference effect at the metasurface. In the case of no interference, the two photons will choose either output with a 50% chance, while in the case of perfect interference, both photons will always choose the same random output port.

    Fig. 2  Illustration of the measurement setup.

    a The two-photon source creates a photon pair with orthogonal linear polarizations by spontaneous parametric down-conversion (SPDC). The two photons are temporally delayed relative to each other by τ with a Michelson interferometer containing a polarizing beam splitter (PBS) and quarter-wave plates (QWPs). The photon pair passes through the metasurface where the NOON state is generated. The spatially entangled state is then analyzed by a coincidence measurement system in two different configurations with single photon detectors (Dn). PMF polarization-maintaining fiber, SMF single mode fiber, M mirror, PC polarization controller, TDC time-digital converter. b Scanning electron microscopy images at 45° (left) and the top view (right) for a small area of the fabricated silicon metasurface (scale bar: 1 µm)

    To characterize the generated quantum state, we perform two different coincidence measurements for various time delays τ. First, we measure the number of coincidences between both output channels of the metasurface. The generated NOON state should not contribute to the number of registered coincidences, ideally leading to zero coincidence counts. However, when the initial $|1_H\rangle$ and $|1_V\rangle$ photons do not arrive simultaneously at the metasurface, we expect a 50% coincidence probability per inserted photon pair (without losses). Thus, as we vary the time delay τ, we expect the well-known Hong-Ou-Mandel (HOM) correlation dip. Note that a visibility higher than 50% verifies the quantum character of interference for these HOM experiments33. Second, we measure the number of coincidences between the two outputs of a 50:50 beam splitter that has been placed in one of the output channels of the metasurface. Coincidence counts for this measurement can be obtained only when both photons choose the same output channel of the metasurface. Since the probability for this event is twice as large in the case of interference, we expect a 2:1 ratio in the coincidence counts between τ = 0 and $\tau \to \infty$. Both coincidence measurements are performed simultaneously by using three superconducting nanowire single-photon detectors. One of these detectors (D3) is directly connected to one of the metasurface output channels, while the other two detectors (D1 and D2) are placed behind an integrated beam splitter (a 3-dB fiber coupler), which is connected to the second metasurface output channel. In this configuration, the first coincidence measurement between the two metasurface channels can be calculated as $C_{13} + C_{23}$, where Cij refers to the coincidence between the detectors Di and Dj.

    The coincidences show a clear dip at zero-time delay with a high visibility of 86 ± 4% (Fig. 3a). Note that the visibility clearly exceeds the limit of 50%, which can be achieved with classical coherent light. At the same time, the second coincidence measurement (C12) shows a clear coincidence peak ("anti"-HOM peak) at τ = 0, which confirms that the two photons are always bunched together in one output channel (Fig. 3b). In the case of interference, both measurements show that the probability of at least one photon in each output channel decreases (first measurement), while the probability of at least two photons in one output channel increases (second measurement). Thus, photon bunching occurs (for details, see Supplementary Information).

    Fig. 3  Hong-Ou-Mandel coincidence measurements.

    a Normalized coincidence counts $\left({{C}_{13} + {C}_{23}} \right)$ between the two output channels of the metasurface for a variation of the initial photon time delay. The high visibility beyond the classical limit of 50% confirms the expected quantum interference effect. The reference is obtained for a standard Hong-Ou-Mandel experiment with a standard beam splitter to characterize the quality of the photon source. b Normalized coincidence counts C12 between detectors D1 and D2 for the measurement with the polarization beam splitter in one output channel of the metasurface. The peak in the coincidence counts of the "anti"-HOM measurement confirms that the two photons always take the same output channel
  • Next, we study whether the metasurface also preserves the quantum coherence of the generated state, i.e., the phase relations between the components of the superposition are fixed and not randomly redistributed. Such coherence is important in quantum metrology applications, where phase measurements play a key role. For that, we realized a folded metasurface-based interferometer (MBI) in which the photons pass through the metasurface twice (Fig. 4a). By tilting a 130-µm-thick glass plate in one of the two arms of the interferometer, we introduce a phase difference between the two optical paths. The final state is then separated and analyzed at a polarizing beam splitter (PBS).

    Fig. 4  Quantum measurements on a metasurface-based interferometer.

    a Schematic view of the metasurface-based interferometer using a time delay τ between the two input photons. b Selected time delays τ illustrated at the HOM-dip measurement. c Experimental results for the two-photon state with three different time delays τ after passing through the MBI. The count rates at both detectors are independent of the introduced phase ϕ and the time delay τ. The measured coincidence rates show an oscillatory behavior with lower visibility at higher delaytimes. The obtained visibility values are 86.8 ± 1.1% for the case of no time delay, 67 ± 2% for $\tau = 3.0\, {\mathrm{ps}}$ and 44 ± 5% for $\tau = 17.7\, {\mathrm{ps}}$

    First, we use a strongly attenuated laser as a weak coherent input state. For the input state $\left| \alpha \right._H\rangle\left| 0 \right._V\rangle$, i.e., a coherent state in one input and vacuum in the other, the count rates in both output ports of the MBI show an oscillating behavior. At the same time, the coincidences show an oscillating behavior with the doubled frequency following a ${\mathrm{sin}}^2\left(\varphi \right)$ function (for details, see Fig. S2b of the Supplementary Information). This behavior can be understood from a classical point of view, where the coincidence corresponds to the product of the single counts. The fringe contrast of 90 ± 1% is in good agreement with our theoretical estimations (see Supplementary Information). Note that φ corresponds to the introduced total phase by passing twice through the tilted glass plate.

    Next, we launch one photon per input mode $\left| 1 \right._H\rangle\left| 1 \right._V\rangle$ by using the photon pairs from the SPDC source. We observe that the counts at each individual MBI output channel will be constant regardless of the introduced phase φ (Fig. 4c). This is due to the first-order correlation between two MBI outputs being independent of φ (see Supplementary Information). However, when we determine the coincidences between the two outputs, we observe the same double frequency oscillation from the coherent case, which is now phase shifted according to a ${\mathrm{cos}}^2\left(\varphi \right)$ function. When two orthogonally polarized photons arrive at the metasurface simultaneously ($\tau = 0$), there is no coincidence contribution in the HOM experiment due to the photon bunching effect (as shown in Fig. 4b). In this scenario, path-entangled photon pairs are generated at the metasurface. Thus, the visibility of interference fringes from the MBI is $86.8 \pm 1.1\%$, which is beyond the violation limit of Bell's inequalities ($70.7\%$). In addition, further experiments for various time delays τ between the initial two photons show a reduced visibility of the coincidence rate (see Fig. 4c). When one photon is delayed by 3 ps, the normalized HOM coincidence rate of approximately 50% tells us that the two photons still overlap partially in time. For this partial overlap, the visibility of the interference fringes is 67 ± 2%, which is close to the boundary of Bell's inequalities. If one photon is delayed by more than 17 ps, they arrive at the MBI one after the other. Correspondingly, no path entanglement is generated inside the MBI. This is in good agreement with our experimental visibility of $45 \pm 5\%$ for the coincidence rate.

    In contrast to the coherent case, the coincidence counts can no longer be perceived as the product of the single counts. This pure nonclassical effect is a key feature of quantum interferometry that is closely related to photon entanglement. The peaks in the coincidences result from the second-order correlation of the entangled NOON spin state with circular polarization, which is generated after passing through the metasurface the first time. Passing through the entire MBI, the entangled NOON spin state is disentangled into the original two-photon state $\hat a_H^\dagger \hat a_V^\dagger |0\rangle$ if there is no phase difference between two MBI arms (first term in Eq. (4)). After splitting the state at the PBS, the two photons arrive at the two detectors simultaneously, which causes the maximum coincidence rates. On the other hand, the minima in the coincidences result from the second-order correlation of the entangled NOON state with linear polarizations (second term in Eq. (4)). For phase differences of $\varphi = \left({{n} + \frac{1}{2}} \right){\mathrm{\pi }}, \, ({n}\epsilon {\Bbb Z})$, the output of the MBI is solely determined by the second term of Eq. (4). The two photons are either in the H or V path, but they cannot be in both paths simultaneously. Hence, there is no coincidence contribution, similar to the HOM effect, as shown in Fig. 3.

  • To quantify the quality of the quantum interference and the entanglement that takes place at the metasurface, we compare the visibility of the HOM dip obtained for the metasurface with a reference experiment. The reference experiment is inspired by Grice and Walmsley33 and allows us to determine an upper bound on the achievable HOM visibility, which is approximately $89 \pm 5\%$ (for more details, see Supplementary Information). The visibility of the HOM dip, which depends not only on the quality of the SPDC source but also on the interference strength of the used interference device, clearly surpasses the classical threshold of 50%. Hence, the high HOM visibility of $86 \pm 4\%$ shows the quantum mechanical nature of the measured spatially entangled two-photon NOON state generated at the metasurface.

    The phase information inside the MBI is hidden when performing an intensity (first-order correlation) measurement at each detector. This phase information can be revealed with the help of coincidence (second-order correlation) measurements between the two detectors. This result is similar to the Franson interferometer that is used for verifying the energy-time entanglement34 and for security information coding in quantum cryptography. Furthermore, our metasurface-based interferometer shows the feasibility of quantum sensors based on nanostructured metasurfaces. Note that the double period of the fringes itself is not a quantum signature of the two-photon NOON state since it also appears in the coincidence measurement for the weak coherent state35.

    Integrated photonic quantum experiments are routinely performed using large-scale optical components such as directional couplers and beam splitters. With our experiments, we demonstrate the preparation of spatial entanglement and disentanglement based on a metasurface in a more compact setting. The results are especially remarkable since the metasurface consists of spatially distributed nanostructured elements with slightly different scattering properties. The experiments confirm that quantum entanglement and interference take place at our dielectric metasurface, while phase-sensitive effects (quantum coherence) are preserved. Our findings demonstrate that metasurfaces can achieve an interference performance similar to that oftraditional optical components and are indeed viable candidates for integrated quantum nanosensors and quantum interferometry.

    Here, we focused on a metasurface for entanglement and interference and therefore for state manipulation purposes. Our metasurface operates as one of the basic building blocks of typical photonic quantum circuits, which splits and recombines optical modes in nested interferometers. However, metasurfaces have enormous potential in quantum optics. Their ability to fully control the wavefronts of light can be used to generate multiphoton and high-dimensional entanglement with different spin-OAM. Combining multiple optical functionalities into a single metasurface as an efficient and compact quantum optical device might dramatically improve the performance and even lead to new concepts for practical quantum applications. Since metasurfaces can be used directly at waveguides and fiber-end facets, these hybrid nanophotonics systems for arbitrary basis transformation can be used for robust integrated quantum technologies, from sensor arrays to quantum simulators. In this context, future research has to show whether metasurfaces can directly generate quantum states, such as single photon pairs, in a well-defined and efficient way without the need for an additional source.

  • The authors would like to acknowledge support from Cedrik Meier (Paderborn University), who provided his electron beam lithography system, and Fabian Meier, who assisted with the fabrication. This project has received funding from the European Research Council (ERC) under the European Union's Horizon 2020 research and innovation program (grant agreement No. 724306) and the Deutsche Forschungsgemeinschaft (DFG, German Research Foundation) through the Collaborated Research Center TRR 142 (No. 231447078). G.L. is supported by the National Natural Science Foundation of China (Grant no. 11774145), Applied Science and Technology Project of Guangdong Science and Technology Department (2017B090918001).

Author contributions
  • P.G., M.M. and K.H.L. contributed equally to this work. P.G., M.M. and K.H.L. performed the experiments, K.H.L. and G.L. proposed the idea, P.G. and T.W. conducted the designs and numerical simulations, B.S. fabricated the sample, and N.M. and H.H. prepared the quantum fiber-pigtailed source. C.S. and T.Z. supervised the overall project. All the authors analyzed the data, discussed the results, and prepared the paper.

Data availability
  • All data needed to evaluate the conclusions in the paper are present in the paper and/or the Supplementary Information. Additional data related to this paper may be requested from the authors.

Conflict of interest
  • The authors declare that they have no conflict of interest.

Supplementary information
  • Reference (35)



      DownLoad:  Full-Size Img PowerPoint